Extron-electronics DVI DL 201 Tx_Rx User Guide Instrukcja Użytkownika

68-1531-01 Rev. C11 10DVI DL 201 Tx/RxUser GuideDVI & HDMI®Dual Link DVI Transmitter and Receiver

DVI DL 201 Tx Rear PanelThe illustration below shows the rear panel features of the DVI DL 201 Tx.12V0.4A MAXPOWERDVI-D INPUTLOCAL OUTPUTOUTPUTSDO NOT

DVI DL 201 Rx Front PanelThe illustration below shows the front panel features of the DVI DL 201 Rx.DVI 201 Rx SERIESTx RxCONTROLPASS THRU9 11DVI-D OU

Cable Connections and SwitchesDVI-D InputConnect the DVI-D source device to the female DVI-I input connector.The dual link DVI-D input carries a signa

Twisted Pair Output and InputTerminating shielded cableCAT 5/5e/6/7 twisted pair cable is not provided with the transmitter/receiver pair. You may pur

5. Separate the individual wires, and arrange them so that all eight wires are side by side in the same order as the T586A or T586B standard shown at

ConnectionsUse RJ-45 connectors to link the output from the transmitter to the appropriate input on the receiver. Three CAT 5/5e/6/7 twisted pair (TP)

DDC SwitchesWhen the DVI-D source device boots up, it uses the Display Data Channel (DDC), a two-way communication protocol, to obtain Extended Displa

RS-232 signalsRS-232 signals are bidirectional — signals pass from the control device and replies return from the remote device. To connect the contro

Power Input1. Connect the captive screw connector from the supplied 12 VDC power supply into the power receptacle.CAUTION: Always use a power supply

Configuration and OperationThis section provides information about: z Conguration z Setup and Operation z TroubleshootingConfigurationUsing the EDID Mi

This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipmen

8. Turn off the display and disconnect it from the transmitter.9. Connect the transmitter to the receiver with the three twisted pair cables. z Tran

Using Pass-through Mode with DDC Routed to a Local Monitor1. Set the EDID Minder switch to the off (down) position and the Default EDID switch to the

6. Boot up the source device. The source boots with the resolution and refresh rate of the remote display.NOTE: Because the remote display is the so

TroubleshootingIf the DVI DL 201 Tx/Rx does not provide a high quality output signal, check the following possibilities before contacting your Extron

Image loss or jitter — DVI signals run at very high frequency and are especially susceptible to bad video connections, too many adapters, or cables th

Reference InformationThis section provides information about: z Specications z Included Parts z Optional AccessoriesSpecicationsVideoMaximum data ra

Video output— receiverNumber/signal type ... 1 dual link DVI-D*Connectors ... 1 DVI-I female

Vibration ... ISTA 1A in carton (International Safe Transit Association)Regulatory complianceSafety ...

Included PartsDescription Part Number(1 pair) DVI DL 201 Tx/Rx 60-957-01or (1) DVI DL 201 Tx 60-957-12or (1) DVI DL 201 Rx 60-957-13(1) 12 VDC, 2A pow

MountingThis section outlines the various mounting options available for the DVI DL 201 Tx/Rx:Tabletop PlacementRack MountingUnder-desk MountingThroug

FCC Class A NoticeThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rule

Rack Mounting ProcedureThe unit can be mounted on any of these optional Extron rack systems: z RSF 123: 3.5 inch deep, 1U rack shelf kit (part number

Extron® WarrantyExtron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of pur

Extron USA - WestHeadquarters+800.633.9876Inside USA/Canada Only+1.714.491.1500+1.714.491.1517 FAXExtron USA - East+800.633.9876Inside USA/Canada Only

ContentsIntroduction ... 1About the DVI DL 201 Tx/Rx... 1Features ...

DVI DL 201 Tx/Rx • Contents vi

IntroductionThis user guide contains information about the Extron® DVI DL 201 Tx/Rx signal transmitter and receiver, with information on how to mount,

12V0.4A MAXPOWERDVI-D INPUTLOCAL OUTPUTOUTPUTSDO NOT CONNECTOUTPUTS TO LAN123TxRxCONTROLPASS-THRUSTOREEDIDON1 2 3 ONOFFDEFAULT EDIDEDID MINDERR

Panels and CablingThis section describes the panel features and cabling of the DVI DL 201 Tx and DVI DL 201 Rx: z DVI DL 201 Tx Front Panel z DVI DL 2