Extron-electronics IPL T CR48 Instrukcja Użytkownika

User GuideIPL T CR48IP Link®IP Link Ethernet Control Interface68-738-05 Rev. C08 10

UL Guidelines for Rack MountingThe following Underwriters Laboratories (UL) guidelines pertain to the installation of an IPL T CR48 unit onto a rack.

Furniture or Projector MountingIn addition to using the IPL T CR48 unit on a rack, it can be furniture or projector mounted. You can furniture mount t

Powera Power Connection — Plug the external 12 VDC power supply into this connector. The power supply is included with the unit.WARNING: When wiring

Ethernet/LANb LAN port — Plug an RJ-45 jack into this socket to connect the unit to a computer network. Use a straight-through cable to connect to a

Front Panel IndicatorsThe front panel of the IPL T CR48 has several indicator LEDs that show the current status of communications to and from the unit

IPL T CR48 Reset Mode SummaryMode Activation Result Purpose and NotesUse Factory Firmware1Hold down the recessed Reset button while applying power to

Connection and ConfigurationThis section discusses how to connect and configure the IPL T CR48. Topics that are covered include:  Connecting the Hardw

Contact Closure Input and Relay ConnectionsContact closure input connectionsThe IPL T CR48 can be connected to any relay providing a closure to ground

Initial start upWhen you power on the IPL T CR48 for the first time, there are two ways to set up the IP address: Use the ARP (Address Resolution Pro

4. On the PC, access the command prompt (from the Windows desktop, click Start, then Run, and type Telnet in the Run dialog box) then execute the arp

This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipmen

Configuring the IPL T CR48 using direct PC connectionThis type of connection is used initially to connect to and configure the IPL T CR48. The default s

Communication and ControlThis section describes communication with the IPL T CR48 as well as A/V device control. Topics that are covered include: Po

Relay PortsThe relay ports can be used for remote switching of low level signals. The relays can be activated via software in three ways:1. The Port

Accessing and using the Web serverTo log on and view system status:1. Double-click the Web browser icon on your Windows® desktop to launch your Web b

Establishing or changing system or port settingsThe System Settings screen is used to initially configure or change the configuration of the IPL T CR48.

To set or change the passwords:1. Click the Passwords link on the menu (on the left side of the window). The Passwords screen (figure 17) is displayed

Editing and adding e-mail alertsIf you have created scheduled events or monitoring tasks on the IPL T CR48, you can write an e-mail alert with a messa

Sending an e-mail alert through TelnetTo complete the process of sending an e-mail alert, you must send it through a Telnet session and receive confirm

Managing filesFile Management is a useful tool that allows you to use and upload existing and custom Web pages. Custom pages can be developed using a t

Programmer’s Guide for the Telnet and Web BrowserUsing the Command/Response TableThe following are either Telnet (port 23) or Web browser (port 80) co

FCC Class A NoticeThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rule

Symbol definitions are shown below. An ASCII to HEX conversion table is also provided in figure 21.ASCII to Hex Conversion Table•SpaceFigure 21. ASCII-

X3* = Event data size: bit; Byte (8-bit); Short (16-bit); Long (32-bit) (only first letter is required)NOTE: This parameter is case-sensitive.X3( =

Error responsesWhen the IPL T CR48 receives a valid command, it executes the command and sends a response to the host device. If the unit is unable to

Reserved charactersReserved characters should not be encoded when they appear in their conventional meaning in a URL. For example, do not encode the s

Command/response table for SIS commandsCommand ASCII (Telnet) URL Encoded (Web) ResponseRelay FunctionsPulse RelayX!*3*X6#OX! %2A 3%2A X6# O Cpn X!•R

Command/response table for SIS commands (continued)Command ASCII (Telnet) URL Encoded (Web) ResponseIP Setup CommandsSet Unit name24 E X1@ CN}W X1@ CN

Command/response table for SIS commands (continued)Command ASCII (Telnet) URL Encoded (Web) ResponseClear user password24E • CU}W %20 CU|Ipu • ]Read u

Command/response table for SIS commands (continued)Command ASCII (Telnet) URL Encoded (Web) ResponseReset Web port map24E 80MH}W 80MH|Pmh00080]Disable

Command/response table for SIS commands (continued)Command ASCII (Telnet) URL Encoded (Web) ResponseReset (Zap)/Erase CommandsErase user-supplied Web

Device ControlControl of A/V devices can be accomplished in several ways once the IPL T CR48 has been connected and configured. These include Web pages

6. If passwords were set up for the connected system, you will be prompted to log in as Administrator or User. Otherwise, the system responds with a

Specifications and Part NumbersThis section discusses: Specifications Part numbers for included parts and accessoriesSpecifications Ethernet control

MountingRack mount ... Yes, with optional 1U rack shelfFurniture mount ... Yes, with optional under d

GlossaryThis section provides definitions of terms related to the IPL T CR48.10/100Base-T — Ethernet that uses Unshielded Twisted Pair (such as UTP - C

GlobalViewer (GV) — A set of Web pages (HTML, XML, JS) and graphics that are loaded into the memory of an IPL T CR48. These pages provide an interface

Extron® WarrantyExtron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of pur

Extron USA - WestHeadquarters+800.633.9876Inside USA/Canada Only+1.714.491.1500+1.714.491.1517 FAXExtron USA - East+800.633.9876Inside USA/Canada Only

ContentsIntroduction ... 1About this Guide ... 1About the IPL T CR4

IPL T CR48 • Contents vi

IntroductionThis section gives an overview of the user guide and describes the Extron® IPL T CR48 IP Link® Ethernet Control Interface and its features

Built-in multi-level security — You can control the access to devices attached to the unit. Two levels of password protection provide appropriate secu

Installation and OperationThis section describes the installation and the operation of the IPL T CR48. Topics that are covered include: Installation