Board Setup and Operation
On the MTP T 15HD RSA board there are two DIP switches (switch #1 is for refresh rate, switch #2 is for audio/RS-232), and a
16-position rotary encoder for EDID selection.
The default settings are: DIP switch #1 60 Hz (down), DIP switch #2 audio (down), EDID encoder 1024x768 (position 2).
On the MTP R 15HD RSA SEQ board there are four active DIP switches. They are: switch #1 = Horizontal sync, switch #2 =
Vertical sync, switch 3 = RS-232 communication, switch #4 = Chroma routing, Switches 5 and 6 are not used.
The default settings are: DIP switch #1 H– (down), DIP switch #2 V– (down), DIP switch #3 unidirectional RS-232 (down),
DIP switch #4 is MTP S-video (down), DIP switch #5 and #6 not used (down)
Access to the DIP switches and encoder is via a cut-out in the cover. Either change the settings before installation, or remove
the board from enclosure to access the switches. See below for all DIP switch and EDID settings.
Changing the MPT T 15HD RSA Board Settings
1. Flip the DIP switches to the setting required.
Switch Position Switch #1 Setting Switch #2 Setting
Up/On 50 Hz RS-232
Down/Off (default) 60 Hz Audio
2. Using a small screwdriver, rotate the encoder pointer to the number or letter corresponding to the resolution required.
See below for EDID encoder positions and resolutions:
Position Resolution Position Resolution
0 N/A 8 1366 x 768
1 800 x 600 9 1400 x 1050
2 1024 x 768 (default) A 1440 x 900
3 1280 x720 B 1600 x 1200
4 1280 x 768 C 1680 x 1050
5 1280 x 800 D 1920 x 1080
6 1280 x 1024 E 1920 x 1200
7 1360 x 768 F N/A
Changing the MPT R 15HD RSA SEQ Board Settings
Change any of the four active DIP switches to the settings as shown in the table below.
Switch
Position
Switch #1
Setting
Switch #2
Setting
Switch #3
Setting
Switch #4
Setting
Switch #5
Setting
Switch #6
Setting
Up/On H+ V+ Bidirectional S-Video
green (luma)
blue (chroma)
N/A N/A
Down/Off
(default)
H- V- Unidirectional MTP standard
green (luma)
red (chroma)
N/A N/A
Skew, Level, and Peaking Adjustments
On the rear panel of the MTP R 15HD RAS SEQ board are
three colored LEDs, a recessed select button, and an Adjust
knob. These work in conjunction to allow the user to make
adjustments to image skew delay, level, and peaking.
Referring to the table at right, press the select button as
desired. Rotate the Adjust knob to adjust the selected
function while monitoring the displayed image.
Refer to the Powercage MTP 15HD RSA Series User Guide for details about skew delay, level, and peaking.
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
+81.3.3511.7655
+81.3.3511.7656 FAX
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
+971.4.2991800
+971.4.2991880 FAX
68-1644-50
Rev A
08 10
O
N
1 2
ON
1 2 3 4 5 6
1 = H SYNC
2 = V SYNC
3 = RS-232
4 = S-Video/MTP
5 = Not Used
Button presses Function LED Color
1 Red skew delay Red
2 Green skew delay Green
3 Blue skew delay Blue
4 Level Green (Blinking)
5 Peaking Blue (Blinking)
©2010 Extron Electronics. All Rights Reserved - www.extron.com
2
PowerCage MTP T 15HD RSA and MTP R 15HD RSA SEQ Setup Guide, cont’d
(52 strony)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji