Extron-electronics SGS 408 User Guide Instrukcja Użytkownika

SGS 408Eight Input, High Resolution, Seamless Graphic Switcher68-520-01 Rev. C03 05

Introduction, cont’dSGS 408 Switcher • Introduction1-4

SGS 408 Switcher2Chapter TwoInstallationRear Panel ConnectorsInstallationCable Pinouts

Installation, cont’dSGS 408 Switcher • Installation2-2InstallationRear Panel ConnectorsFront panel features are shown on page 3-2.Figure 2-1 — SGS 408

2-3SGS 408 Switcher • Installation4If desired, attach a computer or other control device to the RS-232 connector.5If desired, attach an RCP 1000 remot

Installation, cont’dSGS 408 Switcher • Installation2-4Tabletop/desktop mountingFor tabletop or desktop placement, install the self-adhesive rubber fee

2-5SGS 408 Switcher • InstallationProjectorSGS 408ProgramMonitorUp to 8 InputsPreviewMonitorPC ComputerPROGRAMFREEZEBLACK12345 67 8CUTTAKEPROGRAMPREVI

Installation, cont’dSGS 408 Switcher • Installation2-6Attaching an RCP 1000To attach an RCP 1000 remote control panel to an SGS 408 switcher, plug one

2-7SGS 408 Switcher • InstallationControl RoomECP 1000RCP 1000ECP 1000EVENT CONTROL PANELSCREENADJUSTSGS 408PROGRAMFREEZEBLACK12345 67 8CUTTAKEPROGRAM

Installation, cont’dSGS 408 Switcher • Installation2-8Making an RCP comm cableUse the following guidelines to make an RCP cable:• At one end, attach a

SGS 408 Switcher3Chapter ThreeOperationFront Panel ControlsDefault ScreenConfiguring the SGS 408Using the Image ControlsSelecting an InputOptimizing

This symbol is intended to alert the user of important operating and maintenance(servicing) instructions in the literature provided with the equipment

Operation, cont’dSGS 408 Switcher • Operation3-2OperationFront Panel ControlsRear panel features are shown on page 2-2.Figure 3-1 — SGS 408 front pane

3-3SGS 408 Switcher • Operation3RCP communication LEDs — Light to indicate that the SGS 408 iscommunicating with an optional RCP 1000 remote control p

Operation, cont’dSGS 408 Switcher • Operation3-45Controls — Display the available controls. The configuration options areavailable by pressing the Me

3-5SGS 408 Switcher • OperationSelecting the input configurationTo select the input configuration, do the following:1. Press the Menu button.2. Press

Operation, cont’dSGS 408 Switcher • Operation3-66. Depending on the input type, color matrix, Beta-cam control, and Luma/Setup control can be set by p

3-7SGS 408 Switcher • OperationFigure 3-10 — Selecting the output sync format3. To select the output sync format, turn the right adjustment knob. The

Operation, cont’dSGS 408 Switcher • Operation3-84. To select the test pattern you want to display, turn the left adjustment knob.Figure 3-12 shows the

3-9SGS 408 Switcher • Operation5. Pressing the leftmost ECP control button toggles between Window and Key(figure 3-15). This determines the function

Operation, cont’dSGS 408 Switcher • Operation3-108. To return the title its original location and size, press the Reset button(figure 3-18).Figure 3-1

3-11SGS 408 Switcher • OperationFigure 3-21 — Setting the program keylock2. To turn the program keylock on or off, turn the right adjustment knob.3. T

QS-1SGS 408 • Quick StartQuick Start — SGS 408InstallationStep 1Install the four rubber feet on the bottom of theSGS 408 switcher, or mount the switch

Operation, cont’dSGS 408 Switcher • Operation3-12 Edit ProgExit Title Lock LCD ResetFigure 3-23 — Performing a reset2. From the reset submenu, select

3-13SGS 408 Switcher • OperationUsing the Image ControlsThe LCD front panel controls allow you to make adjustments to the displayedimage.To access the

Operation, cont’dSGS 408 Switcher • Operation3-14Figure 3-27 — Sizing an image.Filtering an imageTo apply a filter to an image, do the following:1. Fr

3-15SGS 408 Switcher • Operation2. If you want to adjust the program input, press the Level button again.3. To change the contrast, turn the left adju

Operation, cont’dSGS 408 Switcher • Operation3-16Using the Black buttonEach set of inputs (program or preview set) includes a Black button. Pressing

3-17SGS 408 Switcher • Operation•A standard wipe causes the preview image to appear to unroll over theprogram image horizontally or vertically. A sta

Operation, cont’dSGS 408 Switcher • Operation3-18•A square wipe causes the preview image to appear to unroll over the programimage in one of two trans

3-19SGS 408 Switcher • OperationECP key causes any portion of the preview image which is over halfintensity (.35V) to be displayed with the program im

Operation, cont’dSGS 408 Switcher • Operation3-20Figure 3-38 — Setting up the Dissolve effectFigure 3-39 — Setting up the S wipe effectFigure 3-40 — S

3-21SGS 408 Switcher • OperationFigure 3-41 — Setting up the S curtains effectFigure 3-42 — Setting up the H curtains effectFigure 3-43 — Setting up t

Quick Start — SGS 408, cont’dSGS 408 • Quick StartQS-2Adjusting an ImageFrom the default screen, press the indicated button. To adjust the preview im

Operation, cont’dSGS 408 Switcher • Operation3-22Figure 3-44 — Setting up the Square wipe effectFigure 3-45 — Setting up the Title effect3. To select

3-23SGS 408 Switcher • Operation8 XXX.XX KHz XX.XX Hz Title4 XXX.XX KHz XX.XX Hz Key1280 X 1024 @ 60 HzTrue(DVI) only 2.9 SecondsExecutive Mode En

Operation, cont’dSGS 408 Switcher • Operation3-24To disable executive mode, press and hold the leftmost and rightmost menubuttons for two seconds agai

SGS 408 Switcher4Chapter FourSerial CommunicationRS-232 Programmer’s GuideControl Software for Windows

Serial Communication, cont’dSGS 408 Switcher • Serial Communication4-2The switcher’s RS-232 connector can be connected to the serial output port of a

4-3SGS 408 Switcher • Serial CommunicationSGS error responsesWhen the switcher receives an SIS command and determines that it is valid, itperforms the

Serial Communication, cont’dSGS 408 Switcher • Serial Communication4-4ASCII to HEX Conversion Table•Command/response tableSymbol Definitions: = CR/LF

4-5SGS 408 Switcher • Serial CommunicationX15 = Toggle 0 = Off 1 = OnX16 = xxx.xx Hrt = horizontal rate (in kHz) Vrt = vertical rate (in Hz)X17 = Inpu

Serial Communication, cont’dSGS 408 Switcher • Serial Communication4-6COMMAND ASCII RESPONSE DESCRIPTIONHorizontal SizeIncrementX2+:X2Hsz + Increase

4-7SGS 408 Switcher • Serial CommunicationQuery Software VersionQ/q Ver x.xxExample response: Ver 1.23Request Part NumberN/n Nxx-xxx-xxN60-341-01Reque

iSGS 408 Switcher • Table of ContentsTable of ContentsChapter 1 • Introduction ...

Serial Communication, cont’dSGS 408 Switcher • Serial Communication4-8Using the software1. To run the SGS 408 Control Program, double-click on the SGS

SGS 408 Switcher5Chapter FiveTroubleshooting

Troubleshooting, cont’dSGS 408 Switcher • Troubleshooting5-2TroubleshootingThe image should be displayed properly on the screen.If the image does not

SGS 408 SwitcherAAppendix ASpecifications

Specifications, cont’dSGS 408 Switcher • SpecificationsA-2SpecificationsVideoRouting ... 8 x 2 matrixGain ...

A-3SGS 408 Switcher • SpecificationsBaud rate and protocol ... 9600 baud, 8 data bits, 1 stop bit, no paritySerial control pin configurati

Specifications, cont’dSGS 408 Switcher • SpecificationsA-4

SGS 408 SwitcherBAppendix BReference InformationUpgrades and RepairsPart Numbers

Reference Information, cont’dSGS 408 Switcher • Reference InformationB-2Reference InformationUpgrades and RepairsYou can perform the following upgrade

B-3SGS 408 Switcher • Reference InformationFigure B-2 — Installing the DVI connector option2. Insert the DVI connector through the hole that was creat

ii SGS 408 Switcher • Table of ContentsTable of Contents, cont’d68-520-01 Rev. C03 05Implementing an established effect ...

Reference Information, cont’dSGS 408 Switcher • Reference InformationB-4Figure B-3 — Replacing the fuse (viewed from the side)3. If test equipment is

B-5SGS 408 Switcher • Reference InformationFigure B-4 — Locating and replacing ICs3. Remove the existing chip and set it aside, using a standard IC re

Reference Information, cont’dSGS 408 Switcher • Reference InformationB-6Part NumbersRelated part numbersExtron Part Part NumberSGS 408 60-341-01RCP 10

FCC Class A NoticeNote: This equipment has been tested and found to comply with the limits for a Class A digital device,pursuant to part 15 of the FC

© 2005 Extron Electronics. All rights reserved.Extron Electronics, USA1230 South Lewis StreetAnaheim, CA 92805USA714.491.1500 Fax 714.491.1517Extro

SGS 408 Switcher1Chapter OneIntroductionAbout the SGS 408Features

Introduction, cont’dSGS 408 Switcher • Introduction1-2IntroductionAbout the SGS 408The Extron SGS 408 is an eight-input, high resolution, component vi

1-3SGS 408 Switcher • Introduction• 1360 x 765 (plasma) at 60 Hz, and lock*• 1365 x 1024 (plasma) at 60 Hz, and lock*• 1400 x 1050 (SXGA+) at 50 Hz, 6