Extron-electronics MPS 409 Instrukcja Użytkownika

Media Presentation SwitcherMPS 409User GuideSwitchers68-1833-01 Rev. A07 10

Installation This section describes the installation and the operation of the MPS 409, including:• Mounting the Switcher• Rear Panel Connections• C

3. Mechanical loading — Mount the equipment in the rack so that a hazardous condition is not achieved due to uneven mechanical loading.4. Circuit ov

Rear Panel Connections50/60 HzL RTxMIC/LINEINONOFFMICLINELEVEL+48VON1 2HDMIVIDEOVGA/YUVDVI-DOUTPUTOUTPUTOUTPUTOUTPUTOUTPUTOUTPUTOUTPUT12L12121212121

j Mic/Line input — One 3-pole captive screw connector switchable between mic and line level inputs. A two position DIP switch (u) selects mic or line

q HDMI audio output — 3.5 mm stereo connector with audio output from the selected HDMI input. See figure 4 for wiring.r Composite video output — One

Cabling the MPS 409 SwitcherThe MPS switcher can be connected to as many as 9 input devices simultaneously. It can output to as many as four devices (

Operation This section discusses how to connect, configure, and operate the MPS 409. Topics that are covered include:• Front Panel Features• Front Pa

Microphone and Program Audio Controlsh Mic Mute — Toggles the microphone mixer on and off to provide microphone talk-over for the program audio. The

Front Panel OperationThe MPS switcher can be connected to as many as nine input devices and four output displays plus an audio amplifier. It operates i

Input Selection — Single Switcher ModeIn single switcher mode (default) the switcher emulates a single nine input switcher (9x1). In this mode, when a

This symbol is intended to alert the user of important operating and mainte-nance (servicing) instructions in the literature provided with the equipme

Combine ModeCombine mode switches a selected HDMI/DVI input to the HDMI output, deactivating the DVI audio and video outputs. This enables the MPS 409

Program AudioThe selected audio input is routed to the program audio output according to the switcher mode. The input LED selected for program audio o

Audio Gain and Attenuation AdjustmentsIndividual audio inputs can be adjusted over a range of -18 dB to +24 dB using the program audio mute button and

Microphone ControlsMic on/offMic volume and mute are controlled from the front panel. The Mic mute button toggles the Mic input on or off. The corresp

EDID MinderThe DVI and VGA/YUV groups feature EDID Minder, ensuring that each input source reads the EDID of the output display even when not selected

User assigned EDID Mode — Using SIS commands, an EDID file can be selected from a table of 19 EDID files. One additional EDID file location is reserved f

SIS Programming and Control This section discusses SIS programming and control of the MPS 409 including:• Connection Options• Host-to-MPS Communicat

USB Configuration PortDrivers for the MPS 409 USB configuration port are loaded automatically when Dataviewer or Firmware Loader, included on the softwa

Command/Response TableUsing the Command/Response TableThe command/response table is shown on the following pages. Lower case characters are acceptable

Command/response table for SIS commandsCommandASCII Command (host to switcher)Response (switcher to host)DescriptionSwitcher-initiated messagesInput s

FCC Class A NoticeThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rule

CommandASCII Command (host to switcher)Response (switcher to host)DescriptionSwitcher-initiated messagesProgram audio ducking level in talk over modeA

CommandASCII Command (host to switcher)Response (switcher to host)DescriptionSwitcher-initiated messagesStatus command of Mic DIP switchesRead status

EDID NOTES: EDID Minder is only supported on the VGA and DVI video groups. Attempting to assign an EDID file to the HDMI or composite video group (X!

EDID Format Cross-reference TableX1^Native Resolution Refresh Pixel Clock0 Automatic Mode1 800 x 600 60 Hz 40 MHz2 1024 x 768 60 Hz 65 MHz3 1280 x 7

3. From the toolbar, select File > Open.4. Locate the downloaded firmware file and click to select it.5. Click Begin on the main screen. The total

Reference Information This section discusses the specifications, part numbers, and accessories for the MPS 409. Topics that are covered, include:• Spe

ConnectorsVGA inputs ... 2 female 15-pin HDDVI inputs ... 2 female DVI-IHDMI inputs ...

Input impedance ... 510 ohmsOutput impedance ... 75 ohmsMax. input voltage ...

Audio output — program audioNumber/signal type ... 1 stereo, balanced/unbalancedConnector ...

Regulatory complianceSafety ... CE, c-UL, ULEMI/EMC ... CE, C-tick, ICES, FCC Cla

Part Numbers and AccessoriesIncluded PartsThese items are included in each order:Included partsReplacement part numberMPS 409 60-1012-01MBU 149 1U Ful

Cables and ConnectorsWhen using signals with a scanning frequency of 15–125 kHz and running distances of 100 feet or more, use high resolution BNC cab

Assorted ConnectorsCrimp connectors (qty. = 50) Part numberMini HR, BNC Male 100-250-01Gold Plated Male Center Pins for MHR BNC Connectors 100-256-01S

Extron® WarrantyExtron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of pur

vMPS 409 Switcher • Contents Introduction ... 1About This Manual ... 1

MPS 409 Switcher • Contents vi

Introduction • About this User Guide• About the MPS 409• FeaturesAbout this User GuideThis guide contains information to install, configure, and ope

• Program audio switcher — A four input, one output stereo audio switcher allows the audio input of any video group to be selected for the program au

OUTPUTHDMI 312OUTPUT1 2 3100-240V ~ 0.2A50/60 Hz 21OUTPUTOUTPUTVGA/YUVDVI-D1 2OUTPUT1 2OUTPUT 21LEVELMIC+48VLINEONOFFMIC/LINE12ON+-+--+RLPROGRAMAUDI